Whirlpool washer door wont open

When you wash a load of laundry, the door or lid to your Whirlpool washer door wont open washer locks as a safety feature. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the rapidly spinning basket. Newer models will no longer fill with water when the lid is raised, it must be lowered in place for the wash cycle to start.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. The door will not immediately unlock while the cycle runs due to a possible high water level in the washer, high water temperature, tumbling, or spinning. It may take up to five minutes for the washer to stop spinning and draining before the door will unlock. You will hear the door click when it unlocks. Verify that the drain hose is connected per the installation instructions. The drain hose should not be more than 4. See installation instructions for further information.

Whirlpool washer door wont open

This is for your own safety and to prevent water from leaking out of your appliance. Sometimes, the washer door might lock and stay locked. When this happens, something is most likely wrong with one or more internal components, which will need to be repaired or replaced. If you see no risk of water leaking out of your Whirlpool washer and the motor has completely stopped after the cycle, you can unlock the door by following these steps:. If the reset worked, you can use your washing machine normally as the problem was likely not with any components. Below, we discuss the main components to check and how you can fix them. The lid switch has a striker that needs to work correctly for the door to be able to be opened at the end of a cycle. The next possible cause of your Whirlpool washer door not unlocking is a faulty actuator motor. When the actuator motor becomes defective, your washer might turn off during a cycle, which can stop the door from unlocking. The next component to check is the drain pump. Your final option is to replace the main control board. You must be logged in to post a comment. How To Unlock a Whirlpool Washer.

Skip refills or cancel any time. When the actuator motor becomes defective, your washer might turn off during a cycle, which can stop the door from unlocking.

.

When you wash a load of laundry, the door or lid to your Whirlpool washer locks as a safety feature. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the rapidly spinning basket. Newer models will no longer fill with water when the lid is raised, it must be lowered in place for the wash cycle to start. The lid locking mechanism is an important safety feature, and not something that you should try to bypass. Washer baskets in top-load machines spin at extremely fast revolutions in order to remove the water from your laundry. Opening the washer lid while this spins and reaching inside could cause serious injuries. For this reason, modern Whirlpool top-load washers will lock the lid while the machine is running, and the lid will not unlock until the motor has completely stopped. It can take a few minutes for the washer to stop completely, this is normal! The display on your washer control board should have a light that indicates where the washer is in the cycle, and if the machine lid is locked or unlocked. Be sure to wait until the light is out before attempting to open the washer lid, you could damage the machine if you force it open.

Whirlpool washer door wont open

Whirlpool will be using the following information we gathered from the external platform you selected to create your account. In some circumstances, your new washer may arrive with the door locked. This can occur from normal shipping movement.

Chistes buenos para adultos

I acknowledge that my subscription will auto-renew until I cancel via the Subscriptions section of My Account before the refill order date. Verify that the drain hose is connected per the installation instructions. Yes, I'd like to receive occasional special offers, promotions, or other e-mail marketing communications from Whirlpool and its affiliated brands. The actuator presses down on the switch when the lid is closed, which lets the washer know it can start the wash cycle. December 5, For this reason, modern Whirlpool top-load washers will lock the lid while the machine is running, and the lid will not unlock until the motor has completely stopped. The lid switch has a striker that needs to work correctly for the door to be able to be opened at the end of a cycle. Go to Canadian site. It should have a diagram that outlines where each part is. We spend time learning about the problems and projects that our customers are working on, and we make it our job to answer key questions and provide resources for every step along the way. Session Timed Out Your session has expired. Please wait 10 minutes before trying to perform any functions. Go back to previous article. If the door were to be opened mid-cycle with a front-load washer, you may end up with water flowing out of your machine onto the floor.

Whirlpool will be using the following information we gathered from the external platform you selected to create your account.

Replacing this part is as easy as unscrewing the damaged door strike and screwing a new one into place. The control will not accept any input during this time. This prevents the machine from being opened mid-cycle, which would result in water leaking out or poses a hazard from the rapidly spinning basket. Your final option is to replace the main control board. Go back to previous article. See installation instructions for further information. If this was the case, once the machine has drained the door should unlock normally. You will need to use a multimeter to test a control board for continuity. Verify that the drain hose is connected per the installation instructions. Customer Reviews. Complete Your Account Whirlpool will be using the following information we gathered from the external platform you selected to create your account. If you see no risk of water leaking out of your Whirlpool washer and the motor has completely stopped after the cycle, you can unlock the door by following these steps:. Does the drain pump run constantly? You can use a multimeter to test if the lid switch has continuity or not. The next component to check is the drain pump.