Replace pull cord on mower

Eventually, you're lawnmower pull cord will break. Fortunately it's an easy fix.

The pull cord is used to start the lawn mower; it can often become broken or need replacement. Additionally, make sure you have a large table for the replacement and a rag nearby for wiping off any grease and oil. Make sure the the engine is off and the spark plug wire is removed and away from the spark plug before begining. Use a Phillips 2 screwdriver to remove the two 25mm screws on top of the engine cover. Use your hands to lift the engine cover off, separating it from the rest of the engine.

Replace pull cord on mower

This DIY lawn mower repair guide has instructions for how to replace a lawn mower starter rope. Over time, the starter rope can wear out and eventually break, and the mower won't start. You can replace a broken recoil starter rope with a manufacturer-approved replacement part by following the steps below. Remove the dipstick tube from the engine and plug the hole with a paper towel to keep debris from falling into the engine. Remove the bolts securing the blower housing to the engine and remove the housing from the engine. Turn the rope pulley counter-clockwise 7 times to wind the spring. Align the hole in the pulley with the hole in the housing and insert a screwdriver through the holes to keep them aligned as you work. Thread the new rope through the hole in the housing and pulley. Tie a knot in the rope to keep it from slipping out of the pulley. While holding the rope, remove the screwdriver from the holes in the pulley and housing, and let the rope slowly rewind. Attach the other end of the rope to the starter handle. Feed the rope through the hole in the handle and secure it with another knot.

One comment.

Written by: Steve. October 3, As an Amazon Associate we earn from qualifying purchases more. If you own a pull start lawn mower you will eventually find yourself holding the severed handle of a broken starter cord. Here in Florida, two thirds of the year is one continuous lawn mowing session. That translates to lots of cord tugs. Thankfully, starter cord replacement is simple wear and tear maintenance that you can easily do yourself.

Unless your mower is an electric model or less than three years old, breaking or fraying the pull cord on a mower is fairly common. However, repairing or learning how to replace a pull cord on a mower does require a bit of general knowledge. Knowing the name of each pull cord component should make it easier as you go through this guide and help you understand the role of each part. Step 1 — Watch This short video that shows you step-by-step instructions on replacing the pull cord on a lawnmower. Needle-nose pliers. Phillips or 4-in-1 screwdriver.

Replace pull cord on mower

By: Author John Cunningham. Replacing a pull cord can be challenging, especially if the recoil spring gets loose. Taming a recoil spring can be like herding cats.

Betterhash

However, consider upgrading to a high-quality nylon cord for added durability. Why won't my lawn mower move? Remove the fuel tank. Reinstall the fuel tank. Fit the pull handle and double knot. Working with recoil springs can be dangerous; removing the pully from the assembly comes with the risk of the spring breaking free. While holding the rope, remove the screwdriver from the holes in the pulley and housing, and let the rope slowly rewind. Feed the rope through the hole in the handle and secure it with another knot. Fix Your Stuff Community Store. In other words, when you pull the starting cord all the way out, the pulley should be stopped by the knot at the end of the cord, not by the coil spring. That translates to lots of cord tugs.

At some point, all household maintenance tools are subject to wear and tear, and your lawn mower is no exception. A broken lawn mower pull cord is a pretty common problem.

Do Mowers Have Titles? He was also a consumer electronics repair tech and shop owner for a little over 20 years, until his impending obsolescence became impossible to ignore. Remove the engine blower housing. Repair difficulty. Learn how to re…. Then, use a lighter to melt the ends. Check your lawn mower blade regularly and replaced it if it's bent or damaged. Attach the rope to the starter handle. Thanks again! I was able to get the pull cord fixed without hassle at all. Symptoms for gas walk-behind mowers. Cut the rope to the appropriate length. This provides slack to make a new knot where you made your mark earlier.