How to change a headlight bulb in a ford focus

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy.

Indeed I have read many times the advice "Take it to a dealer to get the bulbs changed", but I don't have that sort of money to throw around. Let me start by thanking Benjol for his excellent blog on changing the bulbs on the Mk1 Focus , which gave me the inspiration to try and do the same for the MK2. I hope he doesn't mind if I do this. Handling little fiddly things bulbs, screws, tools over a complicated engine with lots of deep dark holes is fraught with danger. Short of turning the car upside down and shaking it, there's not much anyone can do for you if you lose something and Murphy's law prevents it falling out the bottom. Moral: don't let anything bulbs, screws slip out of your hands, don't leave any tools lying on a handy bit of engine.

How to change a headlight bulb in a ford focus

Log in. Sign up. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. Sort by Oldest first Oldest first Newest first Most reactions. I've never removed the headlights to replace bulbs on the focus. Pass side is easier, no part removal necessary. On the passenger side, remove the rubber boot from the back of the housing, and unsnap the connector from the bulb and pull it out of the way. Then the bulb and ring will just pull out. Reverse the procedure to reinstall On the driver side you may have to remove a few pieces I have an SRI, so I have to remove my air filter to get to the bulb.

Attach the three bolts for the headlight or two, if you are leaving the one off that is under the car, as I have. More by the author:.

Ford's Focus uses a Halogen H7 bulb in its low-beam socket. Open the bonnet and remove the two Torx screws holding the headlight in place, then lift the headlight forward and out of the car. Unplug the wiring connector on the back, then remove the rubber boot weather seal on the back of the headlight. Undo the grey clip holding the headlight bulb in place, then remove the old bulb. Refitting the headlight is the opposite process. Adjusting the headlight aim should be done by professionals to ensure the light doesn't blind oncoming traffic, while also properly illuminating the road in front of the car. How do you change headlight bulb and adjust Ford Focus headlights?

The only tool needed to change any of the headlight bulbs in either the driver or passenger side housing is a Torx T star bit screwdriver. Locate the two screws that hold the headlight assembly in place. One screw is near the outer edge and the other is at the inner corner. Remove the two screws by turning them counter clockwise with a Torx T star bit screwdriver. Set the two screws aside in a safe place.

How to change a headlight bulb in a ford focus

Changing the dipped beam bulb on the old Mk1 Ford Focus can seem daunting, and I have read different ways of doing it. This is the way I was shown by a Ford engineer, and when you have done it once it is very quick and easy. It involves removing the headlight assembly. The main obstacle is the retaining bolt under the car! My local car hardware chain store seemed insistent that the Mk1-facelife Mk 1. The Mk1. Remove the two bolts on the headlight unit as shown in the figure using the 10 mm socket wrench. One is at the top corner, and the other half way along the top of the headlight.

House of cards tv series cast

This is the most inconvenient bit. Carefully remove the plug on the back of the bulb. Newer designs have done away with this. Ford Maverick. By the way, to pickup on a previous comment, my owners manual shows the wrong bulb replacement pictures and doesn't show or detail the bulb inspection covers at all - but give Ford their due - they've made it simple compared back to the Mk1! It will now only be held on with the power connector. Safely discard the old bulb. In fact, I have not bothered to put this back in, the unit is perfectly secure on the top two bolts. My headlamp required a spanner rather than a Torx driver though. More by the author:.

Log in.

Locate the bulb cover found just behind the headlight assembly and remove it by turning it counterclockwise. This is pushed down to release it from the notch that holds it in. Benjilafouine 56 Replies. Use a HB2 replacement bulb for models older than and a HB5 bulb for models produced since Busy Saturday and much night driving. Push down metal bar to release the back cover, and remove it from the hinge slots. The black plastic piece between the headlights does not have to come off. I can only assume a deliberate act by Ford to encourage people to visit a dealer. Push a flat screwdriver in the clip on the power connector and it will pull off may be a bit tight. Loosen one of these or both if removing entirely. Indeed I have read many times the advice "Take it to a dealer to get the bulbs changed", but I don't have that sort of money to throw around. There are plastic arms with clips that come off by pulling up. Short of turning the car upside down and shaking it, there's not much anyone can do for you if you lose something and Murphy's law prevents it falling out the bottom. Step 2 Open the hood using the hood release handle located inside the vehicle under the steering wheel on the left side of the instrument panel. How do you change headlight bulb and adjust Ford Focus headlights?