Fanuc 21i-t parameter manual

Warning Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use.

Upload aoaby. Embed Size px x x x x Warning notices are used in this publication to emphasize that hazardous voltages, currents,temperatures, or other conditions that could cause personal injury exist in this equipment ormay be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, aWarning notice is used. NoteNotes merely call attention to information that is especially significant to understanding andoperating the equipment. This document is based on information available at the time of its publication. While effortshave been made to be accurate, the information contained herein does not purport to cover alldetails or variations in hardware or software, nor to provide for every possible contingency inconnection with installation, operation, or maintenance.

Fanuc 21i-t parameter manual

Follow along with the video below to see how to install our site as a web app on your home screen. Note: This feature may not be available in some browsers. This website or its third-party tools process personal data e. To learn more, please refer to the cookie policy. In case of sale of your personal information, you may opt out by sending us an email via our Contact Us page. To find out more about the categories of personal information collected and the purposes for which such information will be used, please refer to our privacy policy. You accept the use of cookies or other identifiers by closing or dismissing this notice, by scrolling this page, by clicking a link or button or by continuing to browse otherwise. How to install the app on iOS. Log in Register. Search titles only. Search Advanced search…. Forums New posts Search forums.

Including the two characters at thestart of the packet, the four characters used for a command, and the threecharacters at the end, the maximum number of characters in the packet isnine plus the number specified in parameter No.

.

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment. This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems.

Fanuc 21i-t parameter manual

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use. In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used. Notes merely call attention to information that is especially significant to understanding and operating the equipment.

Philips airfryer xxl manual pdf

The synchronous axis returns to the reference position in the same sequence as the manual reference position return when no returntoreference position is performed after the power is turned on. Limit value that ignores the vector when a tool moves on the outside of a corner during tool nose radius compensation Limit value that ignores the vector when a tool moves on the outside of a corner during cutter compensation C. To prevent the feedratecomponent on a rotation axis from exceeding the maximum allowablefeedrate in polar coordinate interpolation mode, the following override isautomatically applied to the feedrate automatic override :. When the machine performs linear and circular interpolation cutting , thesame value must be set for all axes. In this case, specifying P in a G96 block has no effect on the constant surface speed control. For the parameters for the first axis through the fourth axis of parameter No. Type T:The gear selection signal is entered. NOTE This parameter is used to remove only one axis, for example, when a twoaxis or threeaxis amplifier is used. Word to In some parameters,, signs g are Word axis 0 to ignored. CCN When automatic reference position return G28 is specified in the cutter compensation C mode M series or in tool nose radius compensation T series : 0 : The tool nose radius compensation vector is cancelled in movement to an intermediate position. Pressing the [ OPRT ]soft key can also cause the operation select keys to bedisplayed. AUX The least increment of the command of the second miscellaneous functionspecified with a decimal point0 : Assumed to be 0. The parameter screen is then selected. G83 for T series Parameter No. The ignored rotation angle is added tothe next rotation insertion angle.

.

For details, refer to the Specifications BEN. Set the program axis name for each controlled axis, using one of the valueslisted in the following table:. JS3 3 Z Servo X axis motor. In this parameter, set the time time constant used toreach the speed set in parameter No. NRF The first move command such as G00 and G01 after the serial spindle isswitched to Cs axis contouring control performs:. M codes such as M30, M98, and M99 , already used for other purposes, cannot be set. When a command specifying a speed exceeding the maximum speed of the spindle is specified, or the speed of the spindle exceeds the maximum speed because of the spindle speed override function, the spindle speed is clamped at the maximum speed set in the parameter. The positioning direction is specified using a setting data sign, and the overrun distance using a value set here. Fanuc 16i 18i i i Parameter Manual. The user can freely specify the connector to be used for a given axis. Division count in multiple repetitive canned cycle G73 [Data type] 2word [Unit of data] Cycle [Valid data range] 1 to This parameter sets the division count in multiple repetitive canned cycle G Search forums. In response to an S command, the CNC selects a gear according to the speed range of each gear specified beforehand in parameters.