Civil war box plate

The box plate is lead filled stamped sheet brass. It has 2 brass loops on the back for attaching to the cartridge box.

Civil War Relicman , Harry Ridgeway. Research Center: PlateNewYork. P Militia, Eagle Early two part waist plate, wreath only. P Militia-Rectangle Militia rectangle panel plate, eagle facing right with relaxed wings surrounded by 13 stars. Militia rectangle panel plate, eagle facing right with relaxed wings surrounded by 13 stars This stock militia panel plate was available for purchase by the militia units, in the 's or s.

Civil war box plate

.

Militia, rectangle panel plate. Dingee or J I Pittman, who were partners, based on similarity of die design with other marked plates.

.

During the American Civil War, every enlisted infantryman was issued a cartridge box as part of their accoutrements. Initially, the M pattern cartridge box was utilized. Constructed from leather, it featured a large outer flap which was secured to the base of the box via a sewn-on latch tab and a brass finial. The box also included an inner flap with side ears to help keep out water and dirt, as well as an implement pouch for holding musket tools such as a two-blade screwdriver and nipple wrench, extra nipple, and worm. Within the box were two magazine tins that were designed to hold 20 cartridges of. The back of the box featured two vertical sewn-on leather belt loops for wearing on the waist belt, as well as two horizontal loops for a shoulder sling, which was also issued with an ornamental Eagle Breast Plate. In , a new pattern, known as the M, was adopted to accommodate the new. The pattern cartridge box was almost identical to the box and was manufactured in both.

Civil war box plate

The box plate is lead filled stamped sheet brass. It has 2 brass loops on the back for attaching to the cartridge box. Proudly Made in USA. The oval cartridge box plate is lead filled stamped sheet brass. Stamped sheet brass, lead filled. Two loops are embedded into the lead to facilitate fastening the plate on to your cartridge box strap. This plate is supposed to be right in the center of your chest when mounted on the sling per US regulations. Exact copy of the originals. Circa Ohio Breast Plate.

You can never be overdressed or overeducated

It has 2 brass loops on the back for attaching to the cartridge box. However the manufacturing quality of these Maine plates was very poor, suggesting they were made under special contract and not by any of the regular producers of the period, the solder filling on most is crumbling, and some never had filler at all Research Center: PlateMaine. Marked: "W. Manufacturer of this die pattern is not determined, it is believed that these plates were all made after and up to Nickel silver wreath is one part and applied below the wings. Nondug , white around the hooks is corrosion of the solder. This stock militia panel plate was available for purchase by the militia units, in the 's or s. Circa Ohio Breast Plate. Brass plate is stamped on thin sheet brass, solder filled. This plate is supposed to be right in the center of your chest when mounted on the strap per US regulations. Eagle faces right. The Federal sword plate was authorized in , initially intended for commissioned officers carrying a sword. Plate measures 55mm x 87mm approx. For sale Sold.

.

Reference: O'Donnell Campbell, Plate , , or These frame buckles were made during the war in the Confederacy, they were not used by militia units prior to the war and there was no military need for them after the war. Dug plate, breaks and bends, plate is rough but representative. Configured with two iron hooks formed on a loop with ends bent upward, mounted to the shoulder stap of the enlisted soldier. Nickel silver wreath is one part and applied below the wings. Manufacture: Attributed to Emerson Gaylord, based on similarity to marked die designs. Attribution to H. Reference: O'Donnell Campbell, Plate This die pattern is attributed to H. Circa Ohio Breast Plate. This plate is supposed to be right in the center of your chest when mounted on the sling per US regulations. Shield bears bars only. Manufacture: Emerson Gaylord, Springfield Massachusetts, 's to end of the war. It has two brass loop hooks for attaching to the cartridge box. Plate is die stamped, solder filled, configured as cartridge box plate with iron wire hooks bent to form a loop, both ends bent upward.