1968 mustang hood scoop

All Steel Hood with complete steel under bracing and Mount Hardware designed to fit 67 or 68 Mustang. Features shelby Styled Functional Scoop! This all steel replacement hood for 67 - 68 Mustang builds is made from premium quality stamped steel and features the Hood scoop with functional dual openings. This hood will bolt right to your stock hood hinges with the standard bolts using the included mounting hardware, 1968 mustang hood scoop.

Select Your Submodel. Shelby GT Shelby GTKR. Quantity: 1 Pair. Faithful reproductions of factory hood inserts from Goodmark will come in handy if you want to bring

1968 mustang hood scoop

Ford identified the functional fiberglass hood scoop used on Mustangs using basic part number 16C Based on parts found "in the wild" it appears that at least three different hood scoops were used on Mustangs over the course of model year production. The last version was itself replaced by Ford with the version identified by service part number C9ZZCC as of March I've also seen a picture of what appears to be a version 2 scoop found on 8F02R, scheduled to be built on 11 July and actually built on 12 July. The Version 1 scoop is shaped similarly to the Version 2 scoop, though the material used and the stud locations are definitely different. Note that there are no molded-in engineering numbers on these scoops. The visible markings on the first two scoops are reproduced from original markings. The markings on the third are thought to be original. Breadcrumb Home. Hood Scoop Primary tabs View active tab Revisions.

The markings on the third are thought to be original. Version 3 found on 8F02R, scheduled for build on July 12, : Black-colored, press-molded fiberglass, 3 studs down each side, one centered rear stud. Comes ready to prep for paint in a black e-coated finish, 1968 mustang hood scoop.

.

Log in. Sign up. JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding. I've purchased all the appropriate parts to install the turn signals in the scoop like on my old Mach 1 see avitar. What is the best way to drill the holes in the hood to allow the electrical to be fed up through the engine compartment into the scoop? FYI, the hood is stock so it has all the appropriate turn signal access holes when viewed from underneath. Suggestions as to process, measurements, required tools, etc would be appreciated.

1968 mustang hood scoop

This fiberglass hood features the dual hood scoops like the original Shelby Mustang, but will work with your stock front valance and headlight housings since it is the same length as the stock steel hood. Steel Reinforced at the hinge mounting point and holes drilled and tapped so it Bolts to stock hinges. Made with very high quality hand-laid fiberglass mat and with high quality marine resins and tooling gels for maximum strength and durability. This hood has an excellent fit! Note About Clearances: Because this hood does not have cross-bracing and it has the scoop, it will give you about 1.

Homage meaning in marathi

Mount this scoop to bring cooler air to your engine, or just for show. This hood is an excellent alternative to the fiberglass hoods available on the market. All Steel Hood with complete steel under bracing and Mount Hardware designed to fit 67 or 68 Mustang. Based on parts found "in the wild" it appears that at least three different hood scoops were used on Mustangs over the course of model year production. May be used as a roof scoop. Give your vehicle that hot performance look it deserves! Hand laid, high quality 6 oz. The Westin Scoops make the transformation easy. Compared to the version 3 scoop below, this one has thicker front ears, a ledge on the front opening, and a small lip across the back. Note that there are no molded-in engineering numbers on these scoops. Installation typically requires sanding, trimming, and filling prior to Thanks for signing up!

All Steel Hood with complete steel under bracing and Mount Hardware designed to fit 67 or 68 Mustang. Features shelby Styled Functional Scoop!

Find the same part for less? Thanks for signing up! The part is designed to be applied to any flat or slightly curved hood Next Primary tabs View active tab Revisions. Add a hot performance look Fit most cars, trucks, and SUVs. Installation typically requires sanding, Shelby GT Compared to the version 3 scoop, this one has thicker front ears, a ledge on the top opening, and a small lip across the back. Scoops and vents are manufactured to withstand years of exposure, adding high-performance, and style to any trucks, SUVs, CUVs and passenger cars. Email Us.